blcklblskt's N64 Blogblcklblskt's N64 Blog

Posted on May 4th 2011 at 05:03:24 PM by (blcklblskt)
Posted under Nintendo 64, Controller, Joystick, How to

Is your Nintendo 64 controller joystick loose and worn out?  If so, you will be pleased to know that it is very easy to replace a loose joystick with either a replacement one, or a good one from a donor controller.  In total, this swap will take about 15 minutes if you're switching joysticks between two controllers, or half that if you have a replacement.

I have always used joysticks from used Grey or Atomic Purple controllers, simply because they are plentiful and cheap as most people tend to use the colored controllers more often than their "boring" brothers.  I have never used a replacement joystick, so I cannot comment on their quality.

After the swap, you will have an N64 controller with a nice tight joystick, and if you used a donor, one with a loose stick.  I will usually sell the loose controllers for what I paid for them, around $5, so that no one feels ripped off.  The buyer gets a cheap official controller, and the seller gets his money back. Smiley


Tools needed: Philips head screwdriver set

Time Required: 5-15 minutes

Difficulty: 2/10





[img width=700 height=525]http://i981.photobucket.com/albums/ae295/blcklblskt/N64%20Controller/1.jpg[/img]

The first step is to remove all 9 screws holding the controller together.  The screws I've shown in red are the largest screws you will be taking out, and there are 7 of them in all.  Next, remove the blue screws.  They are usually pretty tight, and they are the longest screws.  Make sure that you use the correct size screwdriver, otherwise you run the risk of stripping the screw heads.

[img width=700 height=525]http://i981.photobucket.com/albums/ae295/blcklblskt/N64%20Controller/2.jpg[/img]

The second step is to remove the back part of the controller shell.  Here you will see the back of the joystick, which is the black piece.  Remove the yellow screws next and place them aside.  To move the Z-Button board (the small one on the back of the joystick), push the two black pieces of plastic that hold the board in place carefully in the direction of the orange arrows.  Then push the board and rubber piece in the direction of the green arrow.  To remove the connector, place your fingernail between it and pop it out.

[img width=700 height=525]http://i981.photobucket.com/albums/ae295/blcklblskt/N64%20Controller/3.jpg[/img]
You have now removed the joystick itself and can now replace it.  To replace it, simply follow the steps above in reverse, and you will soon have a good controller again!

[img width=700 height=525]http://i981.photobucket.com/albums/ae295/blcklblskt/N64%20Controller/4.jpg[/img]

Bigger mages can be seen on my photobucket account here: http://s981.photobucket.c...klblskt/N64%20Controller/

I hope this helps!


Permalink | Comments [6] | Digg This Article |


Recent Entries
In Which I Describe Pizza Tower at an Exhaustingly Long Length (7/31/2024)
Remasters, Remakes, Rereleases, and Remembering the Past (3/30/2024)
The Top 5 Survival Horror Games for the Sega Dreamcast (2/20/2024)
Trombone Champ Is a Good Game (12/30/2023)
Thoughts on the Nintendo Switch OLED Model (11/21/2023)


Comments
 
Now that's interesting...Never knew it was so simple to replace. Thanks for the tutorial. Smiley
 
I've fixed one controller with a new stick I bought at a local game store. Just as you show, very easy and it felt as good as new. Nice post.
 
Suggestion: post the actual size of the screwdriver. Using the wrong size screwdriver can cause you to strip the screws easily if the person isn't familiar.

Other than that, awesome post. I might just do this and resell my loose controllers, as I've got plenty of "donor" controllers around.
 
Awesome guide.

blck why not submit a link on the DB hardware page to this guide?

I'd love to see more repair/mod guides from members in the DB. I am sure plenty of people here have done one or the other at some pint.
 
Thanks for all the positive feedback guys!

@Shadow: I'm not really sure what size screwdrivers are needed, so I edited it to say that a screwdriver set is needed, and to make sure to use the correct size so as not to strip the screw.

@Izret:  Thanks!  I'll submit it right away.
 
Awesome guide. The pics are fantastic!! I havnt had to do this procedure yet, but I'll have this bookmarked for that inevitable time.

 Login or register to comment
It appears as though you are not a member of our site, or are not logged in.
It appears as though you can not comment currently. Becoming able to comment though is easy! All you need to do is register for the site! Not only will you be able to access any other site features including the forum and collection tools. If you are a registered user and just need to login then you can do so here.

Comment! It's easy, thoughtful, and who knows you might just enjoy it!
                                                                                                                                                                                                                                               
This is blcklblskt's Blog.
View Profile | RSS
In this blog I will try to chronicle my N64 collecting, and will hopefully be able to teach you all about the Nintendo 64 along the way.
Blog Navigation
Browse Bloggers | My Blog
Hot Entries
Hot Community Entries
Site content Copyright © rfgeneration.com unless otherwise noted. Oh, and keep it on channel three.